(25) The WAI fan-forced wall heater is designed for commercial and industrial areas requiring higher KW ratings and quick recovery. The unit provides a burst of heat in areas affected by cold drafts or wide temperature swings.
Efficient Operation : The fan draws air into the top of the grille and discharges warm air downward to distribute heat and keep floors warm and dry. High CFMs create air circulation within the room to provide uniform temperatures.
Extended Capacity : The WAI is available with one or two modules and ratings up to 8000 W and 320 CFM.
(30) The WCI fan-forced wall heater is designed for commercial and industrial areas requiring higher KW ratings and quick recovery. The unit provides a burst of heat in areas affected by cold drafts or wide temperature swings.
Efficient Operation : The fan draws air into the top of the grille and discharges warm air downward to distribute heat and keep floors warm and dry. High CFM’s create air circulation within the room to provide uniform temperatures.
Extended Capacity : The WCI is available with one, two or three modules and ratings up to 12000 W at 480 CFM.
(6) The EWI wall heater has a stylish contemporary design with rounded corners and soft lines for an elegant appearance. This heater is ideal for areas with space restrictions and high heating requirements.
Unique Element Design : Totally concealed ribbon-type heating element provides instant heat for areas that need to be warmed quickly.
Three Models : The standard single-stage heater is controlled by an optional remote line-voltage thermostat. Heater type T has a two-stage thermostat which automatically switches from 750 to 1500 watts as needed. Heater type TZ is furnished with an additional 0-60 minute mechanical timer that provides manual operation at 1500 watts during occupied periods, then resumes normal two-stage ...
(11) The WLI wall heater is designed for recessed mounting into shallow 2-inch by 3-inch stud walls. It provides heat in a quiet, efficient manner. Single units can heat small areas and multiple heaters can be used in large or odd shaped rooms.
Mounting Options : Units can be surface or recessed mounted, vertically or horizontally, in one of four positions. A tapered recess box assures a tight fit when mounted into the wall. All models listed are single-phase.
(12) The WRI register wall heater is ideal for use as a primary heat source in small areas or as supplemental heat in more spacious areas. Multiple heaters can be used to effectively heat large or odd-shaped rooms.
Installation Options : Units are designed for recessed mounting into shallow 2-inch by 3-inch stud walls or surface mounting with the use of an optional box.
Safety : Finned tubular elements provide electrical isolation from accidental contact.
Temperature Control : An optional thermostat can be field installed in the heater or a remote thermostat can be used. All models listed are single-phase.
(67) The CUI cabinet heater offers a unique combination of quality, efficiency, reliability and flexibility. The attractive cabinet design blends into any commercial decor.
Mounting Options : The cabinet heater can be mounted on the floor, wall or ceiling. It can also be recessed into the wall or ceiling as required. Twelve air inlet and outlet combinations are available.
Simplified Maintenance : The insulated front panel is hinged to allow for easy access.
Quiet Operation : The blower wheel is mounted directly on the motor shaft to reduce the noise level.
Fresh Air Inlet : Manual or optional power-operated inlet allows fresh air to enter through the rear of the heater and mix with re-circulated room ...
(70) The CDI/CDIR ceiling heaters are designed for commercial applications. CDI heaters are designed for surface mounting and most can be adapted for T-Bar installation with an optional kit. The CDIR heater is designed for recessed mounting and installation into 2-feet by 2-feet ceiling grids. The CDIR comes with a built-in flange; an additional trim ring kit is not required.
Enhanced Performance : These heaters set new industry standards with ratings up to 10000 W and 700 CFM in single and three-phase 208, 240 and 480 voltages.
Increased Comfort : The side draw-through inlet with down discharge promotes circulation within the space for uniform temperatures and increased comfort.
(20) The CCI ceiling heater is designed for commercial use in areas where no wall space is available. It provides supplemental heat to prevent cold drafts or wide temperature swings.
Extended Capacity : CCI heaters are available as single or double modules with ratings up to 8000 W and 320 CFM in 480 volt single-phase.
Control Options : Heaters can be controlled by a building management system with the addition of a low voltage relay.
Flexible Mounting : Units can be surface mounted, recessed or installed in T-Bar ceiling systems. All models listed are single-phase.
(2) The TSI heater is designed for installation in places where other heaters do not fit. These heaters can be installed into the toe space or kick space below a cabinet, in the soffit above a cabinet or into risers of a stairway.
Multiple Wattage : Quick disconnect lead wires allow output conversion from 1000 to 500 Watts.
Over-temperature Protection : Automatic reset thermal cutout is provided for primary over-temperature. More convenient than thermal fuses, which require field replacement when over-temperature conditions occur.
Two-piece Construction :Unit is designed for easy installation. The fan, motor and controls are factory assembled into a sheet metal box with a removable front grille.
(5) The FFI floor heater is compact to fit into tight spaces. It is designed to mount between the floor joists.
Unique Design : The heater features a separate housing and core assembly. The core assembly is completely prewired with leads and an electrical connection plug, which can be removed for service and cleaning without disturbing the housing or field wiring.
Safety Screen : A protective screen prevents foreign objects from falling onto the heating elements or interfering with the fan.
St. Louis, MO 63144